series amel5-maz 5 watt | ac-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052e r8.h 1 of 4 north america only features: models single output model input voltage (vac/hz) input voltage (vdc) temperature range (oc) output voltage (v) output current max (a) maximum capacitive load (f) efficiency (%) amel5-3.3smaz 90-264/47-440 120-370 -25 to +80 3.3 1. 5 2200 68 amel5-5smaz 90-264/47-440 120-370 -25 to +80 5 1 1100 70 amel5-12smaz 90-264/47-440 120-370 -25 to +80 12 0.42 680 73 amel5-15smaz 90-264/47-440 120-370 -25 to +80 15 0.333 330 73 amel5-24smaz 90-264/47-440 120-370 -25 to +80 24 0.21 220 75 amel5-3.3semaz 90-264/47-440 120-370 -40 to +80 3.3 1. 5 2200 68 amel5-5semaz 90-264/47-440 120-370 -40 to +80 5 1 1100 70 amel5-12semaz 90-264/47-440 120-370 -40 to +80 12 0.42 680 73 amel5-15semaz 90-264/47-440 120-370 -40 to +80 15 0.333 330 73 amel5-24semaz 90-264/47-440 120-370 -40 to +80 24 0.21 220 75 models dual output model input voltage (vac, hz) input voltage (vdc) temperature range (oc) output voltage (v) output current max (a) maximum capacitive load (f) efficiency (%) amel5-5dmaz 90-264/47-440 120-370 -25 to +80 5 0.5 470 72 amel5-12dmaz 90-264/47-440 120-370 -25 to +80 12 0.21 220 73 amel5-15dmaz 90-264/47-440 120-370 -25 to +80 15 0.168 150 75 amel5-5demaz 90-264/47-440 120-370 -40 to +80 5 0.5 470 72 amel5-12demaz 90-264/47-440 120-370 -40 to +80 12 0.21 220 73 amel5-15demaz 90-264/47-440 120-370 -40 to +80 15 0.168 150 75 input specifications parameters conditions typical maximum units current (full load) 115 vac 120 ma 230 vac 70 ma inrush current <2ms (cold start) 115 vac 10 a 230 vac 20 a leakage current 0.2 ma external fuse recommended slow blow type 1.5 a input dissipation (no load) <0.3 w start up time soft start 15 ms under voltage protection 89 vac ? i/o isolation 4000vac ? rohs compliant ? operating temp: -40 o c to +80 o c or -25 o c to +80 o c ? energy star compliant ? input: 90-260vac, 47-440hz, or 120-370vdc ? ultra small package ? over load, over voltage, short circuit protection ? soft start cb
series amel5-maz 5 watt | ac-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052e r8.h 2 of 4 north america only output specifications parameters conditions typical maximum units voltage accuracy 2 % line regulation 0.5 % load regulation (single output) 0-100% load 0.5 % cross regulation (dual output) 25% load - 1 s t out, 100% load ? 2 n d out 5 % transient recovery time 200 s transient response deviation 25% load step 2 % of vout minimum load 0 % ripple & noise 20mhz bandwidth 100 mv p-p hold-up time (minimum) 15 ms isolation specifications parameters conditions typical rated units tested i/o voltage 3sec 4000 vac isolation resistance >1000 m ? general specifications parameters conditions typical maximum units switching frequency 132 khz start up time 900 ms over load protection auto recovery, hiccup mode >116% over voltage protection zener diode clamp short circuit protection continuous short circuit restart auto recovery operating temperature with derating above 50oc refer to the models table above o c storage temperature -40 to +95 o c maximum case temperature 100 o c temperature coefficient 0.02 % / o c cooling free air convection humidity non condensing 20 ~ 95 % rh case material plastic resin + fiberglass (flammability to ul 94v-0) weight 30 g dimensions ( l x w x h) 2.03 x 1.10 x 0.70 inches 51.5 x 28 x 17.8mm mtbf > 400 000 hrs (mil-hdbk -217f, t=+25 o c) note: all specifications in this datasheet are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. environment approval parameters conditions shock wave form: half sine wave acceleration amplitude: 5gn bump duration: 30 ms number of bumps: 18 (3 in each direction for every axis) converter operation before and after test, body mounted (on chassis) vibrations test mode: sweep sine 10-100hz, speed 0.05hz/s displacement: 1mm acceleration: 3g 3 loops 30min one cycle, 3h total, every axis tested converter operation before and after test, body mounted (on chassis)
series amel5-maz 5 watt | ac-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052e r8.h 3 of 4 north america only safety specifications parameters agency approvals culus, ce, cb standards medical electrical equipment iec\en\ul 60601-1 , csa-c22.2 no. 601.1-m90 information technology equipment en 60950-1:2006+a11:2009 emi - conducted and radiated emission en55011, class b harmonic current emissions iec/en 61000-3-2, (en60555-2) voltage fluctuations and flicker iec/en 61000-3-3, (en60555-3) electrostatic discharge immunity iec 61000-4-2 rf, electromagnetic field immunity iec 61000-4-3 electrical fast transient/burst immunity iec 61000-4-4 surge immunity iec 61000-4-5 rf, conducted disturbance immunity iec 61000-4-6 power frequency magnetic field immunity iec 61000-4-8 voltage dips, short interruptions immunity iec 61000-4-11 pin out specifications dimensions pin single dual 1 ac input (n) ac input (n) 2 ac input (l) ac input (l) 3 +v output +v output 4 -v output common 5 no pin -v output div: 0.2 (5.08) 5 ?- 0.047 (? 1.2) top view 1 2 3 4 5 dimensions: inch (mm) case tolerance:? 0.012 (0.30) pin pitch tolerance: ? 0.012 (0.30) 1.10 (28.00) 0.40 (10.16) 0.40 (10.16) 2.03 (51.50) 1.80 (45.72) 0.80 (20.32) 0.11 (2.89) top view 1 2 3 4 5 17.80 (0.70) 0.2 (5.08) (min) ?0.04 (1.00)
series amel5-maz 5 watt | ac-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052e r8.h 4 of 4 north america only derating note: 1. datasheets are updated as needed and as such, specifications ar e subject to change without notic e. once printed or downloaded , datasheets are no longer controlled by aimtec; refer to www.aimtec.com for the most current product specifications. 2. product labels shown, including safety agency cert ifications on labels, may vary based on the date manufactured. 3. mechanical drawings and specifications are for reference only. 4. all specifications are measured at an am bient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specifie d. 5. aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. cas numbers and other limited information are considered proprietary an d may not be available for release. 6. this product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control sys tems or other such applications which necessitate specific safety and regulatory standards ot her the ones listed in this datasheet. 7. warranty is in accordance with aimtec?s st andard terms of sale available at www.aimtec.com.
|
